收藏本站
SAW Components
SAW RF filter
B4060
1575.42 MHz
Data sheet
ESD protection of SAW filters
SAW filters are E lectro S tatic D ischarge sensitive devices. To reduce the probability of damages
caused by ESD, special matching topologies have to be applied.
In general, “ESD matching” has to be ensured at that filter port, where electrostatic discharge is
expected.
Electrostatic discharges predominantly appear at the antenna input of RF receivers. Therefore
only the input matching of the SAW filter has to be designed to short circuit or to block the ESD
pulse.
Below three figures show recommended “ESD matching” topologies.
For wideband filters the high-pass ESD matching structure needs to be at least of 3 rd order to
ensure a proper matching for any impedance value of antenna and SAW filter input. The required
component values have to be determined from case to case.
Cs1
Cs3
Cs1
Cs3
Lp2
to output
matching
Lp2
to output
matching
Fig. 1 MLC varistor plus ESD matching
Fig. 2 Suppressor diode plus ESD matching
In cases where minor ESD occur, following simplified “ESD matching” topologies can be used
alternatively.
Cs1
Cs3
Lp2
to output
matching
Fig. 3 3 rd order high-pass structure for basic ESD protection
In all three figures the shunt inductor Lp2 could be replaced by a shorted microstrip with proper
length and width. If this configuration is possible depends on the operating frequency and
available pcb space.
Effectiveness of the applied ESD protection has to be checked according to relevant industry
standards or customer specific requirements
For further information, please refer to EPCOS Application report:
“ ESD protection for SAW filters ”.
This report can be found under www.epcos.com/rke.Click on “Applications Notes”.
Please read cautions and warnings and
important notes at the end of this document.
5
January 31, 2013
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
B39162B4300F210 FLTER SAW 1.57542GHZ LOWLOSS SMD
B39162B7840C710 FILTER SAW 1.57542GHZ SMD
B39162B9000C710S9 FILTR SAW 1.57542GHZ LOWLOSS SMD
B39162B9037E910 FILTER SAW 1.57542GHZ SMD
B39162B9415K610 FILTER SAW 1.57542GHZ SMD
B39162B9416K610 FILTER SAW 1.57542GHZ SMD
B39162B9417K610 FILTER SAW 1.57542GHZ SMD
B39182B7744C810 FILTER SAW 1.8425GHZ LOWLOSS SMD
相关代理商/技术参数
B39162-B4060-U810 制造商:TDK-EPC 功能描述:SAW Filter 1575.42MHzFrequency 50Ohm SMD 8Pin QCC8D 制造商:EPCOS 功能描述:SAW Filter 1575.42MHzFrequency 50Ohm SMD 8Pin QCC8D
B39162B4066U510 功能描述:信号调节 RF 1542 RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39162B4300F210 功能描述:信号调节 B4300 1575.42MHz GPS AEC-Q200 RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39162B4308P810 制造商:TDK EPCOS 功能描述:FILTER SAW SMD RF 1575.42MHZ NAVIGATION
B39162B4310P810 功能描述:信号调节 B5093 SAW IF-FILTER 140MHz RoHS:否 制造商:EPCOS 产品: 频率: 频率范围: 电压额定值: 带宽: 阻抗: 端接类型: 封装 / 箱体: 工作温度范围: 封装:Reel
B39162B4313P810 制造商:TDK EPCOS 功能描述:FILTER SAW SMD RF 1588.66MHZ NAVIGATION
B39162B4327P810 功能描述:FILTER SAW SMD 制造商:epcos (tdk) 系列:* 零件状态:有效 标准包装:1
B39162B4340P810 功能描述:CSSP3 DPX CU-FRAME 制造商:epcos (tdk) 系列:* 零件状态:有效 标准包装:5,000